参数分级管控（A/B/C）A级参数，应完全由省公司集中管控和修改。BCAAAAABBBTacPci英文名称跟踪区码中文名称物理小区识别码频段指示中心载频的信道号小区带宽上下行子帧配置特殊子帧模式参考信号功率天线端口信号功率比小区PDSCH采用固定功率分配时的PA取值BandIndicatorEarfcnBandWidthSfAssignmentSpecialSfPatternsReferenceSignalPowerPbPaACellReservedForOperator小区预留给运营商使用指示UseACellBarred小区禁止接入指示ATimeAlignmentTimerCommo上行时间对齐定时器nCAntennaPortsCount小区支持的发射天线端口数目AMaxHarqTx上行HARQ最大传输数量APeriodicBsrTimer周期性BSR上报定时器ARetxBsrTimerBSR重传定时器AModificationPeriodCoeff修改周期系数AUlCyclicPrefixLength上行循环前缀长度ADefaultPagingCycle默认寻呼周期ANB寻呼分组个数定义PLMN网络的公用跟踪区码（0-65535）。该标识用于跟踪区域。一个小区最多能有1个跟踪区码。（参见TS 36.300）该属性持有小区的物理小区识别码（包括集中式和分布式两种分配情况），取值范围为(0到503)。如果是集中PCI分配（参见TS 36.300），IRPManager通过写入该属性，生成一个具体的值（specific value）。 整数，取值范围为(1-43)见3GPP TS36.101，TS36.104指定链路中心载频的信道号（0至65535）。信道号与物理频率之间的映射，参见3GPP TS 36.104。指定链路的信道带宽，枚举{1.4, 3, 5, 10, 15,20},参见TS 36.101,36.104。TDD EUTRAN小区的上下行子帧配置号（0到6），参见3GPP TS 36.211。TDD EUTRAN小区的特殊子帧配置号（0到8），参见3GPP TS 36.211。小区相关的下行参考信号的发射功率（-60至50）。参见 3GPP TS 36.331。Pb（0至3）。参见TS 36.213。p-a参数取值范围：ENUMERATED {dB-6, dB-4dot77, dB-3, dB-1dot77,dB0, dB1,dB2, dB3}规范参数名称：cellReservedForOperatorUseCell status and cell reservations are indicated in theSystemInformationBlockType1 by means of two Information Elements,cellBarred and cellReservedForOperatorUse.取值范围说明：ENUMERATED {reserved, notReserved}规范参数名称：cellBarredCell status and cell reservations are indicated in theSystemInformationBlockType1 by means of two Information Elements,cellBarred and cellReservedForOperatorUse.取值范围说明：ENUMERATED {barred, notBarred}规范参数名称：timeAlignmentTimerCommonTimeAlignmentTimer is used to control how long the UE is considered uplinktime aligned. Corresponds to the Timer for time alignment in TS 36.321.Value in number of sub-frames. Value sf500 corresponds to 500 sub-frames,sf750 corresponds to 750 sub-frames and so on.取值范围说明：ENUMERATED { sf500, sf750, sf1280, sf1920, sf2560,sf5120,sf10240, infinity}规范参数名称：antennaPortsCountParameter represents the number of cell specific antenna ports where an1corresponds to 1, an2 to 2 antenna ports etc. see TS 36.211, 6.2.1.取值范围说明：ENUMERATED {an1, an2, an4, spare1}规范参数名称：maxHARQ-TxMaximum number of transmissions for UL HARQ in TS 36.321.取值范围说明：ENUMERATED {n1, n2, n3, n4, n5, n6, n7, n8, n10, n12, n16,n20, n24, n28, spare2, spare1}规范参数名称：periodicBSR-TimerTimer for BSR reporting in TS 36.321. Value in number of sub-frames. Valuesf10 corresponds to 10 sub-frames, sf20 corresponds to 20 sub-frames andso on.取值范围说明：ENUMERATED {sf5, sf10, sf16, sf20, sf32, sf40, sf,sf80,sf128, sf160, sf320, sf0, sf1280, sf2560,infinity, spare1}规范参数名称：retxBSR-TimerTimer for BSR reporting in TS 36.321. Value in number of sub-frames. Valuesf0 corresponds to 0 sub-frames, sf1280 corresponds to 1280 sub-framesand so on.取值范围说明：ENUMERATED {sf320, sf0, sf1280, sf2560, sf5120,sf10240,spare2, spare1}规范参数名称：modificationPeriodCoeffActual modification period, expressed in number of radio frames=modificationPeriodCoeff * defaultPagingCycle. n2 corresponds to value 2,n4 corresponds to value 4, n8 corresponds to value 8 and n16 correspondsto value 16.取值范围说明：ENUMERATED {n2, n4, n8, n16}规范参数名称：UL-CyclicPrefixLengthParameter: Uplink cyclic prefix length see 36.211 [5.2.1] where len1corresponds to normal cyclic prefix and len2 corresponds to extendedcyclic prefix.取值范围说明：ENUMERATED {len1, len2}规范参数名称：defaultPagingCycleDefault paging cycle, used to derive ‘T’ in TS 36.304 . Value rf32corresponds to 32 radio frames, rf corresponds to radio frames and soon.取值范围说明：ENUMERATED {rf32, rf, rf128, rf256}规范参数名称：nBParameter: nB is used as one of parameters to derive the Paging Frame andPaging Occasion according to TS 36.304 . Value in multiples ofdefaultPagingCycle ('T'). A value of fourT corresponds to 4 *defaultPagingCycle, a value of twoT corresponds to 2 * defaultPagingCycleand so on.取值范围说明：ENUMERATED {fourT, twoT, oneT, halfT, quarterT,oneEighthT,oneSixteenthT, oneThirtySecondT}
